T5 Dream Link programming problem

[Grumps]

Just acquired a new T5 Dream Link -- entered the latest file ( 103 ) - did factory set - went to satellites and am missing all the ones I need 110 , 119 , 91 and 129 -- have read and tried everything that is suggested here - even switched usb sticks -- still nothing - have tried everything except dropping it on the floor - shut the
power switch of every time I loaded a program and did the factory reset - each time -- unplugged it and let it sit for quite some time and still nothing - shut the power off on the back several times --- same

HELP

Grumps

[Hunter11]

Go to system info in the menu and see what file is installed.

http://www.satfix.net/showthread.php...HD-Set-Up-Info

[Grumps]

checked on the menu and 1.03.00 looks to be the file

[Hunter11]

Is your thumb drive formatted to fat32 if it is then delete the file you have on the stick and load it again from here in the files section. It's possibly corrupt the one you have.

[Grumps]

The module's that were sent to me are DL 100 's

From the info that I've read is that they're supposed to be the new SK 200's ------------ right ????????????

[Hunter11]

Have a look:
http://www.satfix.net/search.php?searchid=2668014

It is the 103 file that has the sats in it for scanning.

[KIDWCKED]

dropping it on the floor wont help..the dl100 is the mod required..factory reset-load lastest bin and factory reset again..

[Grumps]

Ok fellows -- formatted the USB stick -- reloaded the T5_0103_0625 file - did a factory set on the receiver - loaded the new file --- did a factory set - shut off the receiver --- still isn't showing the satellites ( 110 , 199 etc )

[KIDWCKED]

Have a look:
http://www.satfix.net/search.php?searchid=2668014

It is the 103 file that has the sats in it for scanning.

search links are only available too the person searching

Ok fellows -- formatted the USB stick -- reloaded the T5_0103_0625 file - did a factory set on the receiver - loaded the new file --- did a factory set - shut off the receiver --- still isn't showing the satellites ( 110 , 199 etc )

Dreamlink T5 HD Set Up Info

[steven charles]

friend theres something wrong with the factory file your downloading if your not getting any sats on the menu.

[Grumps]

Thanks for the help fellows -- going to call it a night -- been on attempting this programming since 6:30AM -- the system is working great with the Jynx box hooked up again - will try again tomorrow afternoon --

[Hunter11]

Found these possible solutions for you c/p

ok, got it now, Unzipped factory file, loaded it on usb, then loaded in receiver. Then deleted off usb, unzip new bin, load on usb, then load in receiver. Only way i could get them to load. Mabey my 1 gig usb was too small for both files at once? I dont know, but i got everything up and running. Thanks for all your help
---------------------------------------------------------------------------------------------------------------------------------------------------

omahaking
02-16-2012, 09:30 PM
If you are missing 82, 91, 110, 119, and 129 within your antenna setup menu after a bin load, I noticed this on the factory and 11115 bin... sometimes they werent there...just go to the Configuration, System recovery, Click delete all channels YES, and Factory Set YES.

Go back to the Antenna setup and they will be there!

Edit; as Torpainter states in the next post (13), use the 102 file.

[torpainter]

Load the 102 file instead. Its the last file put out by the dreamlink team Go into menu,configuration ,system recovery ,factory set

[erratic81]

Load the 102 file instead. Its the last file put out by the dreamlink team Go into menu,configuration ,system recovery ,factory set

Curious as to why you suggest the 102 file vs the 103 file

[dishuser]

Curious as to why you suggest the 102 file vs the 103 file

read what you quoted