Results 1 to 5 of 5

Thread: XFTA Setup Help

  1. #1
    Join Date
    Sep 2014
    Posts
    4
    Satfix Buxs
    50
    Thanks
    0
    Thanked 0x in 0 Posts

    Unhappy XFTA Setup Help

    I am trying to use my CW800s with XFTA router using X-fta-xx-client-920-Techno-Cyber for the router and bin files v2.66 (I also tried v2.42) and after following different instructions which most are the same with some differences, I still can't make it working, so would you please help me by answer the following questions:

    1. please confirm the below ini files setup.
    2. how to see if the xfta is connected (X-fta-xx-client-920-Techno-Cyber doesn't have log viewer).
    3. there is no run and stop buttons, does it mean it is running as long as it is connect to power?

    Note: I have replace the user id and password with 111 and the domain with aaa.

    caid.ini
    # Up to 8 CaID's can be remapped.
    #1841=1815
    1802:1816

    servers.ini
    # Up to 8 servers can be listed here.
    111111111111:111111111111@aaaaaaaaaaaaaaaaa:35955/6103403445406970987123412134
    # Example:
    # [email protected]:50060/1234123412341234123412341234
    # [email protected]:50061/1234123412341234123412341234
    # [email protected]:50062/1234123412341234123412341234
    # [email protected]:50063/1234123412341234123412341234
    # [email protected]:50064/1234123412341234123412341234
    # [email protected]:50065/1234123412341234123412341234
    # [email protected]:50065/1234123412341234123412341234

    xx-client.ini
    # Serial port receiver is connected to.
    serial_port=/dev/tts/0

    # Set baud to 19200 for most Viewsat, XFactor and CNX receivers that used
    # a dongle.
    # Set baud to 115200 for most other receivers and Viewsats running SSSP
    # firmware.
    serial_speed=115200

    # Control word retrieval timeout in seconds.
    server_timeout=10

    # Number of attempts before connecting to a new server. Setting to '0' will
    # make the client try the next server after first failure.
    server_retries=1

    # Receiver protocol
    # 1 - Viewsat/X-Factor
    # 2 - CNX
    # 3 - SSSP Viewsat/SSSP Pansat/Coolsat
    # 4 - Captiveworks
    receiver_protocol=4

    # If set to 1, CaID reported by the receiver will be ignored and ECM will be
    # sent to server even if there is a CaID mismatch. If you are using a single
    # provider you should set this to 1.
    ignore_caid=1

  2. #2
    Join Date
    Oct 2012
    Posts
    37
    Satfix Buxs
    294
    Thanks
    0
    Thanked 16x in 11 Posts

    Default

    like this

    1841=1815
    1802=1816

    [xx-client.ini]

    servers.ini

    [email protected][/email]:50060/1234123412341234123412341234
    # [email protected][/email]:50061/1234123412341234123412341234
    # [email protected][/email]:50062/1234123412341234123412341234
    # [email protected][/email]:50063/1234123412341234123412341234
    # [email protected][/email]:50064/1234123412341234123412341234
    # [email protected][/email]:50065/1234123412341234123412341234
    # [email protected][/email]:50065/1234123412341234123412341234

    xx-client.ini
    # Serial port receiver is connected to.
    serial_port=/dev/tts/0

    # Set baud to 19200 for most Viewsat, XFactor and CNX receivers that used
    # a dongle.
    # Set baud to 115200 for most other receivers and Viewsats running SSSP
    # firmware.
    serial_speed=19200

    # Control word retrieval timeout in seconds.
    server_timeout=10

    # Number of attempts before connecting to a new server. Setting to '0' will
    # make the client try the next server after first failure.
    server_retries=1

    # Receiver protocol
    # 1 - Viewsat/X-Factor
    # 2 - CNX
    # 3 - SSSP Viewsat/SSSP Pansat/Coolsat
    # 4 - Captiveworks
    receiver_protocol=1

    # If set to 1, CaID reported by the receiver will be ignored and ECM will be
    # sent to server even if there is a CaID mismatch. If you are using a single
    # provider you should set this to 1.
    ignore_caid=1
    Last edited by greg; 10-06-2014 at 12:25 AM.

  3. #3
    Join Date
    Sep 2014
    Posts
    4
    Satfix Buxs
    50
    Thanks
    0
    Thanked 0x in 0 Posts

    Default

    greg, do you have spaces before the username? and I think you are using serial speed 19200 because your receiver is Viewsat, while I have to use 115200 for CW800s, correct?

  4. #4
    Join Date
    Oct 2012
    Posts
    37
    Satfix Buxs
    294
    Thanks
    0
    Thanked 16x in 11 Posts

    Default

    yes set to 115200 for your receiver and the username and password like this
    xxxxxxxxxxxx:[email protected]:35922/6103403445406970987123412134
    # username[email protected]:50062/1234123412341234123412341234
    # username[email protected]:50063/1234123412341234123412341234
    # username[email protected]:50064/1234123412341234123412341234
    # username[email protected]:50065/1234123412341234123412341234
    # username[email protected]:50066/1234123412341234123412341234
    # username[email protected]:50067/1234123412341234123412341234

  5. #5
    Join Date
    Sep 2014
    Posts
    4
    Satfix Buxs
    50
    Thanks
    0
    Thanked 0x in 0 Posts

    Default

    After spending many hours to setup my xfta, I have received answer from poroto40 that file X-fta-xx-client-920-Techno-Cyber is not working with cw800s, therefore, I will start over with a new file xfta-o8.09.2-g1.2.3-wf0.23mex-hgdvb.trx.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •