PDA

View Full Version : No hd chs



jimzzz11
12-15-2012, 05:50 PM
ok i understand most HD on sat 129,but some still on 110,119, here's my problem my sv8000 won scan no hd chs only the SD chs,if the module is burned out shouldn't the box still scan the hd chs?and if possible could some1 show me their settings,use to work but i had to do a factory default and will not scan HD chs.module says detected,iv tried factory file,system clean file,nothing works ,only get SD chls,
TX & XMAS

Glatt
12-15-2012, 06:12 PM
On 110 and 119 you have to change transponders to 21500 and 8psk 2/3 to get HD

jimzzz11
12-15-2012, 06:43 PM
what do i put for FREQ?

Fishbum
12-15-2012, 08:15 PM
If your module is burned out no HD channels will scan in.... must have a working module to scan in HD channels..
Sounds like your module is fine if it says detected.. just need to update your file transponder.. .. i posted this on a nother thread..
1. Load this file onto your receiver, http://phoenix.satfix.net/showthread...12311-with-EPG
2. Do a factory Default
3. Go into each sat 110,119,129 instalation page and re set your settings, exit and save..
4. Go back in to each of your sat instalation pages and re scan each sat (110,119,129) one at a time.

junior1
12-15-2012, 08:32 PM
your link is no good.

jimzzz11
12-15-2012, 09:16 PM
i think its my dish as i have no signal on 12311

junior1
12-15-2012, 09:26 PM
You probably have the wrong settings for your tp. Post what they are and what satellite?

jimzzz11
12-15-2012, 09:31 PM
Sat-110
LNB-Single
Disq-#3
LNB FQ-11250
but when i put on transponder 12311 i have no signal

jimzzz11
12-15-2012, 09:33 PM
Sat-110
LNB-Single
Disq-#3
LNB FQ-11250
but when i put on transponder 12311 i have no signal
tranp 12311 -21500 V Auto Turbo-8
i have the file loaded that Fish sent me still no scan HD ch

Fishbum
12-15-2012, 10:59 PM
hmmm... if your scanning in your sd channels.. that means your sat settings are likely correct,
that leaves either your dish or your module...
What type of module do you have? is it the two piece board or one piece board style.. ??

german sheppard
12-16-2012, 03:39 AM
did you happen to do a factory reset by chance...if you did I beleive this will not let you see the hd up in the 9422 and up...I had to reinstall the hd20 file and rescan which made it all viewable again...hope this tidbit helps.

Fishbum
12-16-2012, 09:15 AM
??????????? Absolutly NO, factory default will not effect scanning for hd in 9422 channels and up..
Factory default will not change your sat transponder file on your receiver. Besides the transponder file on the HD20 bin is out dated... many many channels and transponders changes have been made since that file...
Doing a factory default will not cause that, some thing else that you over looked at the time.. probalby some thing to do with re setting sat settings after you did a factory fefault..


did you happen to do a factory reset by chance...if you did I beleive this will not let you see the hd up in the 9422 and up...I had to reinstall the hd20 file and rescan which made it all viewable again...hope this tidbit helps.